Rust-Oleum Medici Decorative Polyurea Floor Coating

The Medici Decorative Polyurea Floor Coating is a high gloss, UV stable aliphatic polyurea floor coating for use in industrial and commercial facilities. It combines two different finish colors in a simultaneous roller application to obtain a faux stain finish. It is suitable for both interior and exterior.

NOTE: It is not allowed to send this item through air mode. Surface mode is enabled for the same. Thus, shipping will be done through surface.

Features of Medici Decorative Polyurea Floor Coating

• 100% UV stable decorative finish
• Fast dry coating accepts light traffic in 4-6 hours; full vehicle traffic in 24 hours
• Durable polyurea formula protects against chemicals and abrasion
• Easy roller application creates a consistent finish unlike other concrete stains

How to Apply Medici Decorative Polyurea Floor Coating

Surface preparation

The concrete surface must be free of all dirt, grease, oil, fats, and other contamination. Remove surface contamination by cleaning with Pure Strength 3599 Industrial Cleaner/Degreaser, detergent, or other suitable cleaner. Rinse thoroughly with clean, fresh water and allowed to dry. Note: The substrate must be completely dry prior to application of Medici. Polyurea coatings are sensitive to moisture and can affect proper curing of the coating.

New Uncoated Concrete : New concrete must be allowed to cure for a minimum of 30 days before application. In addition to the aforementioned cleaning, the concrete must be further prepared by mechanical grinding or acid etch to remove all laitance and produce a suitable surface profile.

Previously Coated Concrete : Previously coated concrete must be in good sound condition with the existing coating tightly adhering to the concrete. In addition to the aforementioned cleaning the existing coating must be sanded to dull the finish and produce a slight surface profile. Remove all sanding dust by vacuum. Do not wipe the floor with denatured alcohol or other solvent. If wiping is necessary, use only urethane grade Methyl Ethyl Ketone (MEK).

Application

Apply only when air, material and floor temperatures are between 50-90°F (10-32°C). Do not apply in direct sunlight or when temperature is rising. The coating is applied using a special Medici Roller and Medici Roller Pan. Fill each side of the Medici Roller Pan with the different colors. It is strongly suggested that the Medici Roller be de-linted before use. Use duct tape, but rather than wrapping the duct tape around the roller, wrap a piece of duct tape around your hand, sticky side out, and lightly dab or sweep the roller to pick up and remove loose fibers.

Properties of Medici Decorative Polyurea Floor Coating

Surface preparation The concrete surface must be free of all dirt, grease, oil, fats, and other contamination. Remove surface contamination by cleaning with Pure Strength 3599 Industrial Cleaner/Degreaser, detergent, or other suitable cleaner. Rinse thoroughly with clean, fresh water and allowed to dry. Note: The substrate must be completely dry prior to application of Medici. Polyurea coatings are sensitive to moisture and can affect proper curing of the coating. New Uncoated Concrete : New concrete must be allowed to cure for a minimum of 30 days before application. In addition to the aforementioned cleaning, the concrete must be further prepared by mechanical grinding or acid etch to remove all laitance and produce a suitable surface profile. Previously Coated Concrete : Previously coated concrete must be in good sound condition with the existing coating tightly adhering to the concrete. In addition to the aforementioned cleaning the existing coating must be sanded to dull the finish and produce a slight surface profile. Remove all sanding dust by vacuum. Do not wipe the floor with denatured alcohol or other solvent. If wiping is necessary, use only urethane grade Methyl Ethyl Ketone (MEK). Application Apply only when air, material and floor temperatures are between 50-90°F (10-32°C). Do not apply in direct sunlight or when temperature is rising. The coating is applied using a special Medici Roller and Medici Roller Pan. Fill each side of the Medici Roller Pan with the different colors. It is strongly suggested that the Medici Roller be de-linted before use. Use duct tape, but rather than wrapping the duct tape around the roller, wrap a piece of duct tape around your hand, sticky side out, and lightly dab or sweep the roller to pick up and remove loose fibers. Properties of Medici Decorative Polyurea Floor Coating Manufacturer Rust-Oleum Resin Type Aliphatic Polyurea Weight 3.78 Ltr. Solids by Volume 90% Volatile Organic Compounds <50 g="" l="" td=""> Practical C