Rust-Oleum Zinsser Perma-White Mold & Mildew-Proof Interior Paint

Enhance and protect moisture-prone areas in your home or business with Rust-Oleum Zinsser PERMA-WHITE Mold & Mildew-Proof Interior Paint. This high-performance, low-odor coating has a Lifetime durability guarantee. Perfect for bathrooms, basements, etc.

NOTE: It is not allowed to send this item through air mode. Surface mode is enabled for the same. Thus, shipping will be done through surface.

Features of the Product:-

• Mold & Mildew-Proof paint film- guaranteed for 5 years.
• Washable, scrubbable, stain & moisture resistant finish.
• Self-priming – sticks to surface without sanding.
• Fade Resistant.
• Water-base, low odor.
• Tintable to off-white, pastel and medium colors.

How to Apply Zinsser Perma-White Mold & Mildew-Proof Interior Paint

Surface Preparation

Surfaces should be clean, dry, sound and free of dust, dirt, grease, wax, wall covering adhesive, soap film, loose paintor any contamination that may interfere with adhesion. Remove all existing mold and mildew before painting. If you are concerned about mold and mildew behind walls, underneath flooring, in ventilation systems or other unseen areas, contact a professional who specializes in mold and mildew remediation. For commercial buildings and schools, follow appropriate guidelines for mold removal. Clean surfaces with a solution of one cup household bleach per gallon of water or a quality biocidal wash.

Application

Two coats are required for proper performance and mold & mildew-proof resistance. Apply only when air, material, and surface temperatures are between 50-90ºF (10-32ºC) and the relative humidity is below 80%. Thoroughly mix to ensure any settled pigment is re-dispersed before using. Apply with a synthetic (nylon, polyester or blend) bristle brush, roller, pad applicator or airless sprayer. Follow manufacturers instructions when using spray equipment. For airless spraying use a 0.017" tip at 2000 to 2600 psi. Wear NIOSH approved respirator and provide adequate ventilation.

Properties of Zinsser Perma-White Mold & Mildew-Proof Interior Paint

Surface Preparation Surfaces should be clean, dry, sound and free of dust, dirt, grease, wax, wall covering adhesive, soap film, loose paintor any contamination that may interfere with adhesion. Remove all existing mold and mildew before painting. If you are concerned about mold and mildew behind walls, underneath flooring, in ventilation systems or other unseen areas, contact a professional who specializes in mold and mildew remediation. For commercial buildings and schools, follow appropriate guidelines for mold removal. Clean surfaces with a solution of one cup household bleach per gallon of water or a quality biocidal wash. Application Two coats are required for proper performance and mold & mildew-proof resistance. Apply only when air, material, and surface temperatures are between 50-90ºF (10-32ºC) and the relative humidity is below 80%. Thoroughly mix to ensure any settled pigment is re-dispersed before using. Apply with a synthetic (nylon, polyester or blend) bristle brush, roller, pad applicator or airless sprayer. Follow manufacturers instructions when using spray equipment. For airless spraying use a 0.017" tip at 2000 to 2600 psi. Wear NIOSH approved respirator and provide adequate ventilation. Properties of Zinsser Perma-White Mold & Mildew-Proof Interior Paint Manufacturer Rust-Oleum Resin Type Water-based Acrylic Pigment Type Titanium Dioxide, Zinc Oxide Solvents Water, Glycol Ethers Weight 3.78 Ltr. Volatile Organic Compounds <50 g/l (0.42 lbs./gal.) Wet Film to Achieve DFT (Unthinned material) <50 g/l (0.42 lbs./gal.) Practical Coverage at Recommended DFT Approximately 300-400 sq.ft./gal. (7.4-9.8 m2 /l) depending on application method and surface porosity Dry Times at 70-80°F(21-27°C) and 50% RH 30 minuts to Touch 2 hours to Re-Coat 7-10 days to Full Care Shelf Life 5 years Flash Point >200ºF (93ºC) Safety Information For additional information, see MSDS Technical Data Sheet Click here